Hazard vs risk: the difference between hazard and risk explained

A hazard is something with the potential to cause harm. Risk concerns how likely that harm is to occur and how serious the consequences could be. Understanding this distinction helps you identify problems, assess their significance and choose appropriate precautions (Health and Safety Executive, n.d.a).

In fire safety, a portable heater is a potential ignition source. The risk depends on circumstances such as its condition, how it is used, nearby combustible materials and whether people could escape safely if a fire started.

Identifying the heater is therefore only the beginning. A useful fire risk assessment explains how it could cause harm, who could be affected and whether the precautions are adequate.

What is a hazard?

A hazard is anything that could cause harm. It might arise from equipment, a substance, an activity or the condition of the premises.

Fire hazards include potential ignition sources and materials that could burn or contribute to fire development. Examples include electrical equipment, cooking processes, smoking materials and combustible waste (Home Office, 2023).

A hazard does not mean that an incident is certain to happen. Electrical equipment, for example, may be necessary for normal business activities. The assessment must consider its use and the precautions in place.

What is risk?

Risk involves considering the likelihood of harm and its potential severity. HSE advises assessing who could be harmed, how they could be harmed and whether existing controls are sufficient (Health and Safety Executive, n.d.b).

In a fire risk assessment, this means considering both the possibility of a fire starting and what could happen to people if it did.

Relevant circumstances include:

  • The condition and use of potential ignition sources.

  • The amount and location of combustible materials.

  • Whether occupants are awake, asleep or unfamiliar with the building.

  • Whether anyone needs assistance to evacuate.

  • The adequacy of detection, warning, escape routes and other fire precautions.

An assessment must consider the people and premises together. Identifying ignition sources without examining the consequences of a fire gives an incomplete picture (Home Office, 2023).

Hazard and risk: practical examples

The following examples illustrate the distinction. They are hypothetical situations, not findings from an actual assessment.

Portable heater beside cardboard packaging

Hazard or unsafe condition: Heat source close to combustible material

How harm could occur: Packaging could ignite, exposing people to fire and smoke

Factors affecting the risk: Heater type, separation, supervision and escape arrangements

Combustible waste accumulating in a stockroom

Hazard or unsafe condition: Material that could fuel a fire

How harm could occur: A fire could develop and spread beyond the initial item

Factors affecting the risk: Quantity, ignition sources, storage arrangements and fire separation

Wet floor near an entrance

Hazard or unsafe condition: Slippery walking surface

How harm could occur: Someone could slip and suffer an injury

Factors affecting the risk: How wet the floor is, pedestrian use and how quickly it is made safe

Trailing cable across a walkway

Hazard or unsafe condition: Trip obstruction

How harm could occur: Someone could fall and be injured

Factors affecting the risk: Cable position, visibility, lighting and people using the route

Fire door held open with an unsuitable wedge

Hazard or unsafe condition: Loss of the protection the closed door should provide

How harm could occur: Smoke and fire could spread through the opening

Factors affecting the risk: The door’s function, building layout and occupants’ dependence on the protected route

These examples separate the thing or condition that could cause harm from the circumstances that determine the level of risk.

A wedged fire door also illustrates why fire risk assessment extends beyond sources of ignition. A deficiency may make a fire more dangerous without causing it to start.

The same hazard can create different levels of risk

Consider two hypothetical offices using the same type of portable heater.

In the first office, the heater is suitable for its intended use, positioned according to the manufacturer’s instructions and kept clear of combustible materials. Its condition is checked and staff use it appropriately.

In the second, the heater is damaged, surrounded by packaging and left operating unattended.

The equipment type is the same, but its condition and use are different. Those differences affect the likelihood of a fire.

The consequences also require consideration. A fire affecting an escape route may create a different threat to occupants from one in a location where suitable separation and alternative escape arrangements are available. The assessor must examine the actual conditions before reaching a conclusion.

HSE’s fire safety guidance recommends separating ignition sources from flammable substances and maintaining good housekeeping to reduce the opportunity for fire (Health and Safety Executive, n.d.c).

How do you assess and control risk?

Start by identifying what could cause harm. Then consider who could be affected, how harm could occur and what precautions already exist.

HSE recommends deciding what further action is needed, who will complete it and when it should be completed. Where possible, eliminate the hazard. Where that is not possible, control the risk (Health and Safety Executive, n.d.b).

For fire safety, precautions need to address both prevention and protection. Preventive measures reduce the opportunity for fire to start. Protective measures help safeguard people if a fire occurs. These can include detection and warning, suitable escape routes and arrangements that account for people who need assistance (Home Office, 2023).

A practical assessment should therefore explain:

  1. What was observed.

  2. Who could be harmed and how.

  3. Whether existing precautions are adequate.

  4. What further action is needed.

  5. Who should act and the appropriate completion timescale.

Recommendations should address the circumstances identified. “Improve fire safety” gives the reader little direction. A finding should explain the problem and the action needed clearly enough for the responsible person to respond.

Common mistakes when describing hazards and risks

Recording only the hazard

An entry such as “electrical equipment” identifies a broad category but does not explain the concern.

Specify the relevant condition or activity, how harm could arise and who could be affected. Avoid treating the presence of ordinary equipment as evidence that it is unsafe.

Considering only the likelihood of fire

Fire risk assessment must also consider the consequences for people. Assessing prevention measures alone overlooks whether occupants would receive warning and be able to reach safety (Home Office, 2023).

Assuming precautions remove the hazard

A precaution may reduce risk while the hazard remains. Keeping combustible materials away from a heat source reduces the opportunity for ignition, but the heat source still exists.

Controls must remain effective. Their presence on an assessment form is not evidence that they are being used or maintained.

Treating an example as a confirmed finding

Training exercises may ask you to develop plausible scenarios. In an assessment of real premises, distinguish what you observed from assumptions, information supplied by others and matters requiring further investigation.

A hypothetical example should never be presented as something found during a site inspection.

Frequently asked questions

Are hazard and risk interchangeable?

No. The hazard is the potential source of harm. Risk concerns the likelihood and seriousness of that harm in the circumstances being assessed (Health and Safety Executive, n.d.a).

Can a hazard remain when risk has been reduced?

Yes. Equipment or materials may remain necessary, while suitable precautions reduce the risk arising from their use. HSE’s approach is to eliminate hazards where possible and control the risks where elimination is not possible (Health and Safety Executive, n.d.b).

Does risk assessment only involve preventing an incident?

No. In fire safety, the assessment considers measures to prevent fire and measures to protect people if one occurs. Escape arrangements, warning systems and occupants’ needs are therefore part of the assessment (Home Office, 2023).

Fire risk assessment support and training

London Fire Consultants provides fire risk assessment services and fire safety training through The Fire Safety College.

If you are responsible for premises, enquire about a fire risk assessment. If you want to develop your assessment knowledge and skills, compare our Level 3, Level 4 and Level 5 fire risk assessment qualifications.

References

Health and Safety Executive (n.d.a) Managing risks and risk assessment at work: Overview. Available at: https://www.hse.gov.uk/risk/ (Accessed: 14 November 2026).

Health and Safety Executive (n.d.b) Risk assessment: Steps needed to manage risk. Available at: https://www.hse.gov.uk/simple-health-safety/risk/steps-needed-to-manage-risk.htm (Accessed: 14 November 2026).

Health and Safety Executive (n.d.c) Introduction to fire safety. Available at: https://www.hse.gov.uk/fireandexplosion/fire-safety.htm (Accessed: 14 November 2026).

Home Office (2023) A guide for persons with duties under fire safety legislation. Available at: https://www.gov.uk/government/publications/people-with-duties-under-fire-safety-laws/a-guide-for-persons-with-duties-under-fire-safety-legislation-accessible (Accessed: 14 November 2026).

Previous
Previous

Introducing our interactive fire door check

Next
Next

How to become a fire risk assessor in the UK: 2026 guide